BendPak PL-6000DC страница 8 Скачать руководство пользователя

Страница: 8 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Components

The components of your Lift include:
•

Lift Platform and Ramp

. The metal surface that holds raised Vehicles.

•

Control Console

. Houses the Key Switch, Power Indicator, and Emergency Stop controls.

•

Manual Safety Lock Release

. Releases the Safety Locks to Lower the Lift Platform.

•

Front Support

. A bolt-on section of the Lift Post support.

•

Powerside Post

. The Post (sometimes called a column), on which the Power Unit is mounted.

•

Safety Lock Release Angle

. A section of the Safety Lock Release mechanism.

•

Hydraulic Cylinder

. Drives the Lift Chain to raise and lower the Lift Platform.

•

Power Unit

. Provides hydraulic power to the Hydraulic Cylinders that raise and lower the Lift

Platforms.

•

Junction Box

. Mounted on the Power Unit. Houses the wiring and electrical controls for the Lift.

•

Limit Switch

. Limits the upward travel of the Lift.

•

Lift Carriage

. Rides up and down in the Lift Post driven by a Lift Chain. Attaches to the Lift

Platform.

•

Offside (Shared) Post

. The Offside Post is opposite the Powerside Post. When installing

multiple Lifts next to each other, the Offside Post becomes the

Shared Post

. The Shared Post

for the first Lift becomes the Powerside Post for the second Lift.

•

Powerside and Offside Lift Carriages

. Lift Carriages move up and down in the Lift Posts.

The Carriages are connected to the Lift Platform.

•

Lift Platform Side Beam

. Part of the structure connecting the Lift Carriage to the Lift Platform.

•

Back Plate

. Limit of Vehicle travel on the Lift Platform.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды