BendPak PL-6000DC Скачать руководство пользователя | Manualshive

Страница: 17 / 88

background image

PL-6000DC Two Post Parking Lift

17

P/N 5900273 — Rev. A1 — May 2022

⚠

WARNING

Installing your Lift on a surface with more than a 1% slope (0.57˚) could lead to

injury or even death. Only install the PL-6000DC Lift on a level floor. If your floor is
not level, consider making the floor level by cutting, removing and creating a new

concrete slab or choosing a different location.

Do not install the Lift on cracked or defective Concrete.

Never

install the Lift over Concrete expansion or control joints of any kind.

All Anchors

must

be a minimum of 6 in. (152 mm) away from any expansion seams, control

joints or other inconsistencies in the Concrete.

Never

install a Lift on hand-mixed Concrete.

Do

not

install a Lift on a secondary floor level or on any ground floor with a basement beneath

without written authorization from the building Architect and prior approval of Bend Pak Inc.

Verify the floor is

not

a post-tension slab. If it is a post-tension slab, contact the building

architect before drilling. Using ground penetrating radar may help you find the tensioned cables.

On Post-tension slabs, a qualified technician is required to identify cable locations prior to

cutting or drilling. If there are no signs indicating a Post-Tension Slab, undertake a careful
examination of the exterior of the slab looking for small circular patching areas about 1.5" to 3"

in diameter, typically 2 to 4-feet apart. These patches indicate the ends of the Post-Tensioned

Cables. Another source of information is your local department of Building and Safety. Structural
plans may be retrieved by Building and Safety to determine if the building has a Post-Tensioned

Slab.

⚠

WARNING

Cutting through a Post-Tensioned Cable can result in injury or death. Do not drill

into a post-tension slab unless the building architect confirms you are not going to

hit tensioned steel or you have located it using ground penetrating radar. If colored

sheath comes up during drilling, stop drilling immediately.

⚠

WARNING

Use only the Anchor Bolts that came with your Lift. If you use components from a
different source, you void your warranty and compromise the safety of everyone

who installs or uses the Lift.

⚠

CAUTION

BendPak Lifts are supplied with installation instructions and concrete anchors that

met the criteria set by the latest version of the American National Standard

“Automotive Lifts – Safety Requirements for Construction, Testing, and Validation”,
ANSI/ALI ALCTV. You are responsible for any special regional structural and/or

seismic anchoring requirements specified by any other agencies and/or codes such

as the Uniform Building Code (UBC) and/or International Building Code (IBC).

«
...
15
16
17
18
19
...
»

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

Бренд: IBM Страницы: 72

Бренд: Eaton Страницы: 4

Бренд: Eaton Страницы: 10

Бренд: Vulcan-Hart Страницы: 28

Бренд: probst Страницы: 33

Oerlikon CITOCUT 25C

Бренд: Air Liquide Страницы: 68

CoolBloC C34 DN 32

Бренд: PAW Страницы: 24

Бренд: IDEAL Страницы: 23

Бренд: National Instruments Страницы: 21

Бренд: Kathrein Страницы: 9

Бренд: SALUPO Страницы: 22

Бренд: Balluff Страницы: 4

HS 2000 LARGE FH

Бренд: R. Beck Maschinenbau Страницы: 34

EVO SPEED STAR 380 TC

Бренд: Cebora Страницы: 212

Бренд: mr. steam Страницы: 4

Бренд: Ingersoll-Rand Страницы: 64

Бренд: WALTCO Страницы: 48

Бренд: Bürkert Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды