BendPak PL-6000DC Скачать руководство пользователя | Manualshive

Страница: 60 / 88

background image

PL-6000DC Two Post Parking Lift

60

P/N 5900273 — Rev. A1 — May 2022

Maintenance

Proper and regular maintenance will extend the life of your Lift and reduce downtime due to

component failures.

⚠

DANGER

Before performing any maintenance on your Lift, make sure it is completely
disconnected from power. Do not reconnect it until all maintenance procedures are

finished. The Lift uses electrical energy; if your organization has Lockout/Tagout
policies, make sure to implement them

before

performing any maintenance. If you

come into contact with high voltage/current, you could be injured or killed.

⚠

DANGER

Verify the Lift is resting on a Safety Lock or on the ground

before

performing any

maintenance. Do not work on the Lift if the Safety Locks are not engaged, you

could be injured or killed.

If you need to replace worn, damaged, or broken parts, you

must

use parts from (or approved by) the

original equipment manufacturer (OEM) or parts that meet the OEM’s specifications.

⚠

WARNING

If you use parts not from, approved by, or meeting the specifications of the original
equipment manufacturer, you void your warranty and compromise the safety of

everyone who installs or uses the Lift.

To maintain your Lift

:

•

Daily

: Keep the Lift clean. Wipe up any spills and remove dirt.

•

Daily

: Make a visual inspection of all moving parts and check for damage or excessive wear.

Replace any damaged or worn parts before using the Lift.

⚠

DANGER

Do not use the Lift if the Lifting or Balancing Chains are damaged or extremely
worn. If a Vehicle is raised when you notice the damage or extreme wear, very

carefully lower the Vehicle to the ground, if this can be done safely; if it cannot be

done safely, evacuate the area and make arrangements with trained lift service
personnel to lower the Vehicle. When the Lift is on the ground, take it out of service,

disconnect it from power, and make arrangements with trained lift service

personnel to fix the damage and/or wear.

•

Daily

: Determine the cause of any abnormal noise.

•

Daily

: Verify all safety devices are operating and in good condition.

⚠

WARNING

Do

not

use a Platform if its Safety Lock is damaged or excessively worn.

•

Weekly

: Check all Controls, including Emergency Stop, to make sure they are functioning.

•

Weekly

: Check all Labels on the Lift. Replace them if they are illegible or missing.

•

Monthly

: Grease the lubrication points on the Lift. Use white lithium grease or similar.

•

Monthly

: Check Hydraulic Fluid levels in the reservoir when the Platform is at its lowest position.

Refill as required.

•

Monthly

: Check the inlet filter inside the Hydraulic Oil Reservoir. Clean or replace the Filter as

required.

•

Monthly

: Check Hydraulic Hoses for cracks, abrasion or leaks. Replace as required.

•

Monthly

: Check power supply wiring, if possible. Replace any wiring with cracked or damaged

insulation.

«
...
58
59
60
61
62
...
»

Содержание PL-6000DC

























































































Отзывы:

Нет отзывов

Похожие инструкции для PL-6000DC

Бренд: Baier Страницы: 20

NeverFreeze SX-0810-24

Бренд: ThermoSoft Страницы: 5

MAGNUM TIG THF 238 PRO

Бренд: Spaw Страницы: 10

Бренд: heat-timer Страницы: 40

Бренд: Bame Страницы: 12

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

Бренд: Euroscreen Страницы: 39

RM-208 CB.13.01

Бренд: EasyLine Страницы: 16

Бренд: VIA Technologies Страницы: 2

AIR N ARC I 300 SERIES

Бренд: Vanair Страницы: 130

Бренд: HERKULES Страницы: 162

Бренд: Herz Страницы: 98

Бренд: Brewtools Страницы: 7

Бренд: Sanwa Страницы: 31

Бренд: Heat&Glo Страницы: 33

Бренд: National Instruments Страницы: 27

Бренд: National Instruments Страницы: 125

Бренд: HADEF Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды