BendPak PL-6000DC Скачать руководство пользователя

Страница: 11 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Will My Car Fit?

Your Lift accommodates a wide variety of cars, light trucks, and SUVs.

Width

Considerations for Vehicle width include:
•

Platform width

. The usable width of the Platform is

82.5 inches / 2,100 mm

; the outside

dimension of your tires cannot be wider than this.

All four tires must be fully on the

Platform

; they cannot be on the side structure or on the Ramp. Always center your Vehicles on

the Platform, width-wise.

•

Mirrors

. Mirrors and other accessories may mean that some parts of a Vehicle are much wider

than the rest of the Vehicle. Parking lifts are designed to have lots of open space, but if you are

parking Vehicles next to each other that both have wide mirrors or other accessories, verify they do
not hit each other.

•

Car doors

. Opening Vehicle doors makes the Vehicle wider while they are open. Generally you

want to avoid opening the doors of multiple Vehicles parked next to each other at the same time.

You cannot open a car door while the Vehicle is raised, so this is not an issue for raised Vehicles.

Length

Considerations for Vehicle length include:
•

Platform length

. The usable length of the Platform is

146 inches / 3,700 mm

; your

wheelbase cannot be longer than this.

All four tires must be fully on the Platform

; they

cannot be on the Ramp or beyond the Tire Stop.

•

Overhang

. If a Vehicle’s tires are fully on the Platform, then the parts of the Vehicle hanging over

the Back Stop or the Ramp are not a concern, as long as they do not hit Lift Posts or any other

obstacle.

Height

Considerations for Vehicle height include:
•

Ceiling height

. A typical ceiling height as shown in the figure below is approximately

170

inches / 4,320 mm

. The height of your ceiling determines how much space you can allocate to

the two Vehicles. If you want to park a tall Vehicle on a Platform

and

under the Platform, your

ceiling is going to have to be higher than if you want to park two low-slung Vehicles.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды