BendPak PL-6000DC Скачать руководство пользователя

Страница: 15 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Installation

The installation process includes multiple steps. Perform them in the order listed.

⚠

WARNING

Only use the factory-supplied parts that came with your Lift

. If you use

parts from a different source, you void your Warranty and compromise the safety of

everyone who installs or uses the Lift. If you are missing parts, visit

bendpak.com/support

or call

(800) 253-2363

, extension 191.

Safety

While installing this equipment, your safety depends on proper training and thoughtful operation.

⚠

WARNING

Do not install this equipment unless you have automotive Lift installation training.

Always use proper lifting tools, such as a Forklift or Shop Crane, to lift heavy

components. Do not install this equipment without reading and understanding this
Manual and the Labels on the unit.

Only fully trained personnel should be involved in installing this equipment. Pay attention at all times.

Use appropriate tools and lifting equipment. Stay clear of moving parts.

⚠

WARNING

You

must

wear OSHA-approved (publication 3151) appropriate protective

equipment at all times during installation: leather gloves, steel-toed work boots, eye
protection, back belts, and hearing protection are

mandatory

Tools Required

You may need some or all of the following tools:

•

Rotary hammer drill (or similar)

•

12 mm carbide bit (conforming to ANSI

B212.15)

•

Hammer and crow bar

•

Four-foot level

•

Open-end wrench set, metric

•

Socket and ratchet set, metric

•

Hex key wrench set, metric

•

Medium crescent wrench

•

Torque wrench

•

Phillips and slotted screwdrivers

•

Hammer

•

Chalk line

•

Medium-sized flat screwdriver

•

Tape measure, 25 feet or above

•

Needle-nose pliers

•

Forklift, or Shop Crane 2 Ton capacity

•

White Lithium Grease

•

Machine oil for Chain lubrication

•

Thread Sealant

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды