BendPak PL-6000DC страница 35 Скачать руководство пользователя

Страница: 35 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Installing the Lift Cylinder and Lift Chain

The Lift Cylinder receives hydraulic fluid from the Power Unit. As the Cylinder Rod extends, it drives the

Lift Chain that is attached on one end to the Lift Carriage and on the other end to the Powerside Lift
Post.

To attach the Lift Cylinder and Lift Chain

Attach one end of the Lifting Chain to the Mounting at the Base of the Powerside Post. Refer to the

figure below. Lock the Pin through the Chain and Mount with two 2 mm x 20 mm Split Pins, one

on each side.
Install the Lift Cylinder on the Powerside Post in the holes provided at the bottom of the Post.

Attach the Cylinder to the Powerside Post using the Cylinder Bracket and Two M10 Socket Head

Cap Screws. Refer to the figure below.

Drawing not to scale.

Place the Cylinder Head with Chain Wheel on the Cylinder Rod. Refer to the figure below.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды