BendPak PL-6000DC Скачать руководство пользователя

Страница: 40 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Install the Power Unit

This section describes the mounting of the Hydraulic Power Unit. An Electrician is

not

required to

mount the Power Unit to the Powerside Post.

⚠

DANGER

Risk of explosion: This equipment has internal arcing or parts that may spark and
should not be exposed to flammable vapors. Never expose the Motor to rain or

other damp environments.

⚠

WARNING

Running the Power Unit without Hydraulic Fluid will damage it and this damage is

not covered under warranty.

⚠

WARNING

Damage to the Power unit due to water, detergents, acid and other liquids is

not

covered under warranty.

⚠

WARNING

The Power Unit is very heavy. BendPak strongly recommends you mount the

Power unit with the reservoir empty. One person should support the Power unit in
place while another bolts the unit into place.

To install the Power Unit

Retrieve six M8 x 20 Hex Head Bolts and M20 Flat Washers. Mount the Power Unit using the Hex

Head Bolts and Flat Washers. See figure below.

Содержание PL-6000DC
























































































Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды

BendPak PL-6000DC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PL-6000DC

Отзывы:

Похожие инструкции для PL-6000DC

Бренды по названию

Популярные бренды