manualshive.com logo in svg

Banner SC22-3, Инструкция по эксплуатации

Поделиться
Скачать
Banner SC22-3 Скачать руководство пользователя страница 58

 56     

P/N 133487

Banner Engineering Corp. 

• 

Minneapolis, U .S .A .

www .bannerengineering .com  •  Tel: 763 .544 .3164

Product Name 

 

Instruction Manual

Operating Instructions

6.2.1  Run Mode Screen — OBI

The OBI Run mode screen displays current information about 

the Safety Controller, including:

• The configuration name 
• Safety output status
• Input status
• System status
• XM card status

Figure 6-3. Run mode screen — OBI

Arrowhead designates 

selected safety output

Configuration Name

Safety Output Status

Input Status Cause of 

Output SO1 Status, or 

Required Action

Configuration Name: The top line of the display reads either 

the name of the configuration stored in the Safety Controller, if it 

has been confirmed, or 

Configuration not confirmed

, if it has not .

Safety Output Status: Lines 2, 3, and 4 of the screen display 

the status of the three safety outputs . The selected output 

will have a small arrowhead to its left, on the screen . (The 

arrowhead scrolls through the safety outputs that are OFF, at 

2-second intervals .) Line 5 of the display states the reason for 

the status of the selected safety output .
NOTE:  Output faults are recoverable via a system reset (see 

Section 6 .4) .

Safety Output 

Status Message

Cause and/or Required Action

ON

The safety output is ON .

ON-Delay

The safety output will turn ON when the ON-delay time expires .

OFF

The safety output is OFF . 
Line 5 of the display indicates the reason the safety output is OFF .

OFF-Delay

The safety output will turn OFF when the OFF-delay expires . 
Line 5 of the display indicates the reason the safety output is in an OFF-delay .

Reset Needed

A manual reset operation needs to be performed . 
Line 5 of the display indicates the name of the manual reset input to press .

Fault

A problem has been detected with the safety output . See the troubleshooting table (Section 8 .3 .1) to find additional 
information regarding the fault . 
If the fault is due to an external device monitor (EDM) fault, line 5 of the display indicates the name of the EDM .

Enable Mode

Line 5 of the display indicates Enable Mode if a safety output is in Enable mode .

Содержание SC22-3

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды