Banner SC22-3 Скачать руководство пользователя

Страница: 120 / 128

118

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Appendix C

Edit Inputs menu

ESC→

Edit Configuration menu

Configure the Status Outputs

To configure the status outputs, select Outputs/System

Settings and press OK .

Select Status Outputs and press OK .

Use the left/right arrow keys to select the status output to

configure . In this case, select Status Output 01 and press OK .

The next menu displayed is the Status Output Properties

menu . From this menu you can configure the status output(s) .

Configure:

• Status output 01 to track the state of ES01
• Status output 02 to signal when a reset operation is needed

for Safety Output SO1

Configure Status Output 01

Change the name of 01 by selecting Change Name and

pressing OK .

Use the left/right arrow keys to select the character to be

changed (up to 10 characters) .
Use the up/down arrow keys to change the character (choices

A-Z, 0-9, -, +, or space) .
Set the name to ES01 and press OK .

The display returns to the Status Output Properties menu . The

top line of the display now displays the name assigned to the

status output .

Configure the status output to track an input . Select Select

Function and press OK .

Using the left/right arrow keys, select Track Input and press OK .

The display returns to the Status Output Properties menu .
Configure the status output to track the E-stop input, ES01 .

Select Select Source and press OK .

Using the left/right arrow keys, select ES01 and press OK .

The display returns to the Status Output Properties menu .
Status output 01 is now configured . To save the settings, select

<Done> and press OK .

The display returns to Outputs/System Settings menu .

To configure additional Status Outputs, select Status Outputs,

select the status output to configure and repeat the steps that

were performed for status output 01 .

Содержание SC22-3

































































































































Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды

Banner SC22-3, Инструкция по эксплуатации

Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды