Banner SC22-3 страница 117 Скачать руководство пользователя

Страница: 117 / 128

P/N 133487

115

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Appendix C

Use the left/right arrow keys to select the terminal assignment to

be changed .
Use the up/down arrow keys to change the terminal

assignments .
Set the terminal assignments to S1, S2, S3, and S4, and press

OK .

After the terminal assignments are edited, the display returns to

the Input Properties menu .

Map Outputs

Choose which of the safety output(s) the input will control . Select

Map Outputs in the Input Properties menu and press OK .

To map the input to an output, select the output using the

up/down arrow keys and press OK . A filled-in circle next to an

output indicates the input is mapped to that output . To remove

the input mapping, select the output and press OK . An open

circle indicates the input is not mapped to that output .
Map the E-stop to all three safety outputs, select Save and press

OK .

After mapping the input to the safety outputs, the display returns

to the Input Properties menu .

Set Reset Logic

To set the reset logic, select Reset Logic and press OK .

Use the left/right arrow keys to select the Set Reset Logic

parameter . Select Manual and press OK .

After the Reset Logic parameter is set, the display returns to the

Input Properties menu .

Saving the Input Device Parameters

All of the E-Stop’s parameters have been set . To save the

parameters, select < Done > and press OK .

The display now indicates the input parameters were saved .
Press OK to continue .

The display returns to the Inputs menu .

Содержание SC22-3

































































































































Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды

Banner SC22-3, Инструкция по эксплуатации

Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды