Banner SC22-3 Скачать руководство пользователя страница 55

Страница: 55 / 128

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Configuration — Onboard Interface

Configure Input Device Properties

For each input device, the following parameters must be

configured:

• Name (or use the auto-generated default name)

• Circuit type

• Terminal assignments (or use the auto-generated terminal

assignments)

• Reset logic (for some devices)

• Output mapping or input mapping (depending on device)

Enter Input Device Name — The Enter Name menu is

displayed . A default name automatically appears, but the device

may be renamed (up to 10 characters) .

• Use the left/right arrows to select the character position .

• Use the up/down arrows to select the character for each

position (choices A-Z, 0-9, -, +, or space) .

• When the screen (as shown below) shows the correct device

name, press OK .

Input Properties Menu — The Input Properties menu is used

to:

• Select the input device’s circuit type

• Edit the terminal assignments, if needed

• Select the output(s) (or input), the input will control

• Select between automatic and manual reset logic

(depending on device)

←

→

Safety Input

(Section 5.5.1)

Non-Safety

Input

(Section 5.5.2)

←

→

←

→

itc

E-

tiv

lin

itc

Add Input

(Section 5.5)

Add an Input continued

Select the Circuit Type of the Input — Use the up/down

arrows to select Select Circuit Type, and press OK .

NOTE: See Appendix A for more information about safety circuit

integrity levels and the capabilities of each circuit type .

• The Select Circuit Type menu appears .

• Use the left/right arrows to select the desired circuit type (a

dual-channel, 4-terminal circuit type is shown below) for the

input device and press OK .

• After the circuit type is selected, the display returns to the

Input Properties menu .

Edit the Terminal Assignments — When the input circuit type

is selected, the Safety Controller automatically assigns the next

available terminals for the input device . To view and change

these terminal assignments, select Edit Terminals, and

press OK .

• Use the left/right arrow buttons to select the terminal

assignment to be changed .

• Use the up/down arrows to change the terminal assignment .

• When the terminal assignments are as desired, press OK .

NOTE: Only unassigned terminals can be assigned .

(Exception: Terminals used for a specific input device can be

assigned twice during the edit process, if the same terminals

will be used, in a different order, for this specific device .)

• After the terminal assignments are approved, the display

returns to the Input Properties menu .

Содержание SC22-3

































































































































Результаты поиска

Содержание SC22-3

Отзывы:

Бренды по названию

Популярные бренды

Banner SC22-3, Инструкция по эксплуатации

Результаты поиска

Содержание SC22-3

Отзывы:

Бренды по названию

Популярные бренды