Banner SC22-3 страница 7 Скачать руководство пользователя

Страница: 7 / 128

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Overview

Status Indicator

Condition

Indicates Controller Status

All Indicators OFF

—

Initiation Mode

Power

ON Green
OFF

Power ON
Power OFF

Status (Controller Mode)

ON Red
Flashing Red
OFF

Configuration mode
Lockout mode
Run mode

Transmit/Receive Tx/Rx

Flashing Green
OFF

Transmitting or receiving data (a link is established with the PC)
Not transmitting or receiving data

Safety Output SO1, SO2, SO3

ON Green
ON Red
Flashing Red
Flashing Green

Safety output ON
Safety output OFF
Safety output fault detected
Safety output waiting for reset

Figure 1-4. Onboard Interface, including push buttons, LCD display and status indicators

SC22-3

Safety Controller

Power

Status

Tx/Rx

SO1

SO2

SO3

Moves cursor up or causes items

within a list to be displayed as

the cursor is moving up through

the list. May also be used to make

selection settings.

Moves cursor down or causes

items within a list to be displayed

as the cursor is moving down

through the list. May also be used

to make selection settings.

Moves cursor to the

right or performs

selection setting.

Enters or stores the item highlighted in the

display as the intended selection or may be used

to toggle a setting

Moves cursor to the pre-established point

in the program to re-establish

a menu reference point.

Status

Indicators

Moves cursor to

the left or performs

selection setting.

NOTE: The Onboard Interface functions are covered in more detail in Section 5 and the OBI tutorial, appendix C .

Содержание SC22-3

































































































































Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды

Banner SC22-3, Инструкция по эксплуатации

Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды