Banner SC22-3 страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 128

background image

P/N 133487

31

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

System Installation

CAUTION . . .

Shock Hazard

Always disconnect all power from the Safety
Controller and the guarded machine before

making any connections or replacing any component. Use
extreme caution to avoid electrical shock at all times. Serious
bodily injury or death could result.

WARNING . . .

Proper Wiring

The generalized wiring configurations shown
are provided only to illustrate the importance of

proper installation. The proper wiring of the Safety Controller
to any particular machine is solely the responsibility of the
installer and end user.

0V dc

S3

S4

Y3

Y1

13

23

33

Feedback (optional)

* Installation of transient (arc) supressors across the coils of MPCE1 and MPCE2
is recommended (see Warning)

Y4

Y2

14

24

34

S1

S2

K2

K1

Machine

Control

MPCE

2

MPCE

1

IM-T-9A

Input Terminals

SC22

*

*

1A

1B

2A

2B

3A

3B

A2

SO1

SO2

SO3

+24V dc

Figure 3-14. Two-channel EDM hookup to IM-T-9A interface module

The IM-T-9A interface module depicted in this figure is shown in two-channel
EDM hookup. The IM-T-11A module is connected in a similar manner.
Depending on the application, each safety output requires a separate and
individually wired IM-T-..A module.
See Section 3.6.1 on external device monitoring and Section 3.6.3 on
interfacing safety stop circuits.

WARNING . . .

Use of Transient

Suppressors

Transient suppressors are
recommended. They MUST be
installed across the coils of the
machine control elements. NEVER
install suppressors directly across
the contacts of the MPCEs. It is
possible for suppressors to fail as
a short circuit. If installed directly
across the contacts of the MPCEs, a
short-circuited suppressor will create
an unsafe condition.

WARNING . . .

OSSD Interfacing

To ensure proper

operation, the Safety Controller
output parameters and machine
input parameters must be considered
when interfacing the solid-state
safety outputs to the machine inputs.
Machine control circuitry must be
designed so that:
• The maximum cable resistance value

between the Safety Controller solid-
state safety outputs and the machine
inputs is not exceeded,

• The Safety Controller’s solid-state

safety output maximum Off state
voltage does not result in an ON
condition, and

• The Safety Controller’s solid-state

safety output maximum leakage
current, due to the loss of 0V, will not
result in an ON condition .

Failure to properly interface the
safety outputs to the guarded
machine could result in serious
bodily injury or death.

«
...
31
32
33
34
35
...
»

Содержание SC22-3

































































































































Отзывы:

Нет отзывов

Похожие инструкции для SC22-3

Бренд: Canon Страницы: 2

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 6

Бренд: WAC Страницы: 5

Бренд: YASKAWA Страницы: 340

1020 CAN-RS232-RS422 MFL

Бренд: PENKO Страницы: 29

Бренд: Cypress Страницы: 571

Бренд: Conductrix Wampfler Страницы: 23

Бренд: Carel Страницы: 2

Бренд: Timotion Страницы: 9

Бренд: Conel Страницы: 52

Бренд: Revox Страницы: 57

Бренд: Wittenstein Страницы: 52

Turbo-V 250 series

Бренд: Varian Страницы: 79

Бренд: M-system Страницы: 7

Бренд: J+J Страницы: 6

Бренд: DCU Tecnologic Страницы: 2

Бренд: Pacostar Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды