Banner SC22-3 Скачать руководство пользователя

Страница: 43 / 128

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Configuration — PC Interface

4.3.5 System Reset

The Controller requires a system reset under certain conditions:

• To place the Controller into Run mode after it has been

configured .

• To recover from certain conditions (e .g ., lockouts) .

To perform a system reset, either provide a 24V dc signal on

the System Reset input (located next to the Status Output O10

terminal), or cycle power .
When the configuration is successfully confirmed, the Controller

will switch to Run mode .

4.4 Revise an Existing Configuration

When the software program opens, go to File > Open or click
the

icon to browse for the configuration to be changed .

Make changes as described in Section 4 .3 .

4.5 Other Functions

4.5.1 Receive a Configuration from the SC22-3

To receive a configuration from a Controller and display it in the

PCI:

• Connect the SC22-3 Controller to the PC using the USB

cable .

• Apply 24V dc power to the Controller .
• Click on the Receive button

in the tool bar .

• If the configuration is not already confirmed, you may choose

to confirm it at this time .

4.5.2 Send a Configuration to the SC22-3

To send a configuration from the PCI to a Controller:

• Connect the SC22-3 Controller to the PC, using the USB

cable .

• Apply 24V dc power to the Controller .
• Click on the Send button

in the tool bar .

4.5.3 Open a Configuration from the XM Card

Both confirmed and unconfirmed configurations can be sent to

or received from the XM card . To open a copy of a configuration

from the XM card and display it in the PCI:

• Connect the SC-XMP programming tool to the PC using the

USB cable .

• Insert the XM card into the programming tool .
• Go to File > Open From XM Card in the upper-left corner of

the screen .

A message will appear when the operation is complete .

4.5.4 Send a Configuration to the XM Card

Both confirmed and unconfirmed configurations can be sent to

or received from the XM card . To send a copy of a configuration

from the PCI to the XM card (via the programming tool):

• Connect the SC-XMP programming tool to the PC using the

USB cable .

• Insert the XM card into the programming tool .
• Select the Open Folder button

in the tool bar and

open the intended configuration file .

• Go to File > Send To XM Card in the upper-left corner of

the screen .

A message will appear when the operation is complete .

4.5.5 Lock the XM Card

It is important to note that this operation cannot be undone.

Once the card is locked, another configuration can never be

stored on it . This operation is useful when the XM card and its

configuration will be transported to another Controller, or for

storing and archiving a configuration . To lock the XM card so

that the stored configuration cannot be changed:

• Insert the XM card into the SC-XMP programming tool .
• Verify that the correct file is stored on the XM card .
• Go to File > Lock XM Card in the upper left of the tool bar .

A message will appear when the operation is complete .

Содержание SC22-3

































































































































Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды

Banner SC22-3, Инструкция по эксплуатации

Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды