Banner SC22-3 Скачать руководство пользователя

Страница: 52 / 128

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Configuration — Onboard Interface

5.4.3 Outputs/System Settings

Safety Outputs

This option is used to configure the safety outputs . Use the up/

down arrows to select Safety Outputs and press OK . Select the

output to configure in the resulting menu and press OK . You will

be given the opportunity to change the output’s name, and give it

an ON- or OFF-delay .

Status Outputs

This option is used to configure the status outputs . Status

outputs are configured individually . Use the up/down arrows to

select Status Outputs and press OK .

• Use the left/right arrows to select the status output to

configure (O1 to O10), and press OK .

• The Status Output Properties menu appears . This menu is

used to configure the status output to indicate:

— The status of an input device

— The status of a safety output

— A system lockout

— An I/O fault

— The need to perform a system reset

— The need to perform a reset operation on a safety output

— When an input is being muted

Name the Status Output — Use the up/down arrows to select

Change Name and press OK .
• Use the left/right arrows to select the character to be

changed (up to 10 characters) .

• Use the up/down arrows to change the character (choices

A-Z, 0-9, -, +, or space) .

• Press OK when done .

• When the display returns to the Status Output Properties

menu, the top line of the display will display the new name .

Select the function of the status output — Options are:

unassigned (no function), track input, track output, track fault

status, waiting for reset, and mute status . Use the up/down

arrows to select Select Function and press OK .
• Use the left/right arrows to select a function, then press OK .

• The display returns to the Status Output Properties menu .
Select the source for the status output function — Select

Select Source and press OK .
• Use the left/right arrows to select a device and press OK .

• The display returns to the Status Output Properties menu .
Select the signal convention — The options are:

24V = Input Active and 24V = Input Inactive (e .g ., if tracking

an input; see Section 3 .7 for more information) .
• Use the left/right arrows to toggle between the selections

and press OK .

To save the settings for this output, select <Done> and press

OK . The display returns to the Outputs/System Settings menu .

To configure additional status outputs, select Status Outputs,

select another status output and repeat the steps above .

When the last status output is configured, press ESC to return

to the Edit Configuration menu .

System Settings

Select the output’s reset mode, power up mode and whether

mute will be active on power-up .
System Reset — Use the left/right arrows to toggle between

Monitored or Non-Monitored, and press OK .
Power Up Option — Use the left/right arrows to select among

Normal, Auto, or Manual, and press OK .
Mute on Power-Up — Use the left/right arrows to toggle

between Off or On, and press OK .

System

Settings

Terminal

Assignments

Input/Output

Mapping

Status Output

Settings

Status

Outputs

Safety

Outputs

Edit

Configuration

(Section 5.4)

Edit

Input

Delete

Input

Inputs

(Section 5.4.2)

Outputs/System

Settings

(Section 5.4.3)

Configuration

Summary

(Section 5.4.4)

←

→

←

→

←

→

←

→

←

→

Add Input

(Section 5.5)

Save

Configuration

(Section 5.4.5)

Name

Configuration

(Section 5.4.1)

Edit Configuration continued

Содержание SC22-3

































































































































Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды

Banner SC22-3, Инструкция по эксплуатации

Результаты поиска

Содержание SC22-3

Отзывы:

Похожие инструкции для SC22-3

Бренды по названию

Популярные бренды