Baker Hughes Panametrics PanaFlow LC Скачать руководство пользователя страница 70

Страница: 70 / 146

4.4 Fluid and pipe problems

If preliminary troubleshooting with the Error Code Messages

and the Diagnostic Parameters indicates a possible

problem, proceed with this section. Measurement problems

fall into two categories:
• Fluid problems
• Pipe problems
Read the following sections carefully to determine if the

problem is related to the fluid or the pipe. If the instructions

in this section fail to resolve the problem, contact

Panametrics for assistance.

4.4.1 Fluid problems

Most fluid-related problems result from a failure to observe

the flow meter system installation instructions, as described

in Chapter: Installation.
If the physical installation of the system meets the

recommended specifications, it is possible that the fluid

itself may be preventing accurate flow rate measurements.

The fluid being measured must meet the following

requirements:
• The fluid must be homogeneous, single-phase,

relatively clean and flowing steadily.

Although a low level of entrained particles may have

little effect on the operation of the XMT1000, excessive

amounts of solid particles will absorb or disperse the

ultrasound signals. This interference with the ultrasound

transmissions through the fluid will cause inaccurate

flow rate measurements. In addition, temperature

gradients in the fluid flow may result in erratic or

inaccurate flow rate readings.

• The fluid must not cavitate near the measurement point.

Fluids with a vapor pressure relatively close to process

pressure may cavitate near the measurement point.

Cavitation can usually be controlled through proper

system design.

• The fluid must not excessively attenuate ultrasound

signals.

Some fluids, particularly those that are very viscous,

readily absorb ultrasound energy. In such a case, signal

warning and error message will appear on the display

screen to indicate that the ultrasonic signal strength is

insufficient for reliable measurements.

• The fluid soundspeed must not vary excessively.

The XMT1000 will tolerate relatively large changes in the

fluid sound speed, as may be caused by variations in

fluid composition and/or temperature. However, such

changes must occur slowly. Also, fluctuations in fluid

sound speed due to changes in temperature will likely

recover independently. Rapid fluctuations in the fluid

sound speed, to a value that is beyond ± 20% from that

programmed into the XMT1000, will result in erratic or

inaccurate flow rate readings. This may occur when

changing batch fluids.

Note:

Refer to Chapter 3: Programming, to make sure the

appropriate soundspeed is programmed into the meter.

4.4.2 Pipe problems

Pipe-related problems may result from improper choice in

meter location or errors in programming. The following may

result in problematic installations:

• The collection of material at the transducer location(s).

Accumulated debris at the transducer locations will

interfere with the transmission of the ultrasound signals.

As a result, accurate flow rate measurements are not

possible. Realignment of the transducers often corrects

these problems but, in some cases, wetted transducers

must be used. Refer to

Chapter: Installation for more details on proper

installation practices.

• Inaccurate pipe measurements.

The flow rate measurement accuracy relies greatly on

the accuracy of the programmed pipe dimensions.

Measure the pipe wall thickness and diameter with

the same accuracy desired in the flow rate readings.

Also, check the pipe for dents, pitting or rough surfaces,

eccentricity, weld deformity, straightness and other

factors that may cause inaccurate readings. Refer to

the Chapter: Programming, for instructions on entering

the pipe data.

• The inside of the pipe or pipe is not sufficiently clean.

Excessive buildup of scale, rust or debris inside the pipe

will interfere with flow measurements. Generally, a thin

coating or a solid well-adhered build up on the pipe

wall will not cause problems. Loose scale and thick

coatings (such as tar or oil) will interfere with ultrasound

transmission and may result in incorrect or unreliable

flow rate measurements.

Содержание Panametrics PanaFlow LC



















































































































































Результаты поиска

Содержание Panametrics PanaFlow LC

Отзывы:

Похожие инструкции для Panametrics PanaFlow LC

Бренды по названию

Популярные бренды

Baker Hughes Panametrics PanaFlow LC, Руководство пользователя

Результаты поиска

Содержание Panametrics PanaFlow LC

Отзывы:

Похожие инструкции для Panametrics PanaFlow LC

Бренды по названию

Популярные бренды