Baker Hughes Panametrics PanaFlow LC Скачать руководство пользователя страница 141

Страница: 141 / 146

Certification and Safety Statements

Certification and Safety Statements for PanaFlow PF10 Zx

• When installing this apparatus, the following

requirements must be met:

• Field wiring shall be rated at least 5°C above maximum

ambient or fluid temperature, whichever is greater.

• Connecting cables shall be mounted securely and

protected from mechanical damage, pulling and

twisting.

• Cable entry is ¾” NPT.
• Cable glands of an approved flameproof design are

required. These must be installed according to the

manufacturer’s instructions. Where the cable glands

are provided by Panametrics, the manufacturer’s

instructions, as supplied to Panametrics, will be included

in the documentation.

• Conduit seals are required within 18” of the enclosure
• Cable glands of an approved flameproof design are

required. These must be installed according to the

manufacturer’s instructions. Where the cable glands

are provided by Panametrics, the manufacturer’s

instructions, as supplied, to Panametrics, will be

included in the documentation.

• The system is covered by the certificate numbers

FM13ATEX0070X and IECEx FMG 13.0028X as shown on

the labels below. The system is certified as ATEX and

IECEx: II 2 G Ex d IIB +H2 T6 Gb in Ta = -40°C to +60°C

ambient, Type 4X and IP66. The system temperature

code is dependent upon the process fluid temperature

ranges of -40°C to +150°C. Refer specific conditions of

use for ATEX and US/Canada for more information about

temperature code.

• Unused cable entries must be sealed using a certified

threaded plug.

• Modifications to the flameproof enclosure are not

permitted.

• The apparatus should be de-energized before opening.
• Installation shall be in accordance with the installation

instructions and the National Electrical Code® ANSI/NFPA

70, the Canadian Electrical Code C22.1, or IEC/EN 60079-

14, as applicable.

• Equipment is of type flameproof “d” design and

complies with the standards identified in the table on

page 2.

• The product contains no exposed parts which produce

surface temperature infrared, electromagnetic ionizing,

or non-electrical dangers.

• The product must not be subjected to mechanical or

thermal stresses in excess of more than those permitted

in the certification documentation and the instruction

manual.

• The product cannot be repaired by the user; it must be

replaced by an equivalent certified product. Repairs

should only be carried out by the manufacturer or by an

approved repairer.

• Only trained, competent personnel may install, operate

and maintain the equipment.

• Consult the manufacturer if dimensional information on

the flameproof joints is necessary.

• The product is an electrical apparatus and must be

installed in the hazardous area in accordance with the

requirements of the EU Type Examination Certificate.

The installation must be carried out in accordance with

all the appropriate international, national and local

standard codes and practices and site regulations

for flameproof apparatus and in accordance with the

instructions contained in the manual. Access to the

circuitry must not be made during operation.

• The flameproof joints of the equipment are not intended

to be repaired. Consult the manufacturer if dimensional

information on the flameproof joints is necessary.

• Follow the manufacturer’s instructions to reduce the

potential of an electrostatic charging hazard.

• Consult the manufacturer for genuine replacement

flange fasteners. M10x35 hexagon socket cap screws of

ISO 12.9 DIN912 grade steel (zinc-plated) or better with a

minimum yield strength of 135,000 psi are acceptable

alternatives.

• Consult the manufacturer for genuine replacement

flange fasteners. M10x35 hexagon socket cap screws of

ISO 12.9 DIN912 grade steel (zinc-plated) or better with a

minimum yield strength of 135,000 psi are acceptable

alternatives.

129

Содержание Panametrics PanaFlow LC



















































































































































Результаты поиска

Содержание Panametrics PanaFlow LC

Отзывы:

Похожие инструкции для Panametrics PanaFlow LC

Бренды по названию

Популярные бренды

Baker Hughes Panametrics PanaFlow LC, Руководство пользователя

Результаты поиска

Содержание Panametrics PanaFlow LC

Отзывы:

Похожие инструкции для Panametrics PanaFlow LC

Бренды по названию

Популярные бренды