Avaya Cajun P333T Скачать руководство пользователя страница 93

Страница: 93 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show secure mac port

Use the

show secure mac port

command to display the secure MAC addresses

of a port from the sub-agent CLI. This command is accessed only through
connection to a particular switch.

Note:

This command is not supported by the P330-ML switches.

Note:

If this command is to be implemented on a switch other than the stack master,

a session should be opened to the relevant switch.

The syntax for this command is:

show secure mac port [<module>[/port]]

Output Example:

P330-N> show secure mac port 1

Port Secure-Src-Addrs

------ -----------------

1/17 00-50-04-07-6a-fa

01-02-03-04-05-06

show arp-tx-interval

Use the

show arp-tx-interval

command to display the keep-alive frames

transmission interval.

The syntax for this command is:

show arp-tx-interval

Output Example:

P330-N> show arp-tx-interval

ARP tx interval is set to 5 seconds.

show arp-aging-interval

Use the

show arp-aging-interval

command to display the ARP table aging

interval for gateways’ entries.

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 93 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: