manualshive.com logo in svg

Avaya Cajun P333T, Руководство пользователя, Страница: 5 / 182

Поделиться
Скачать
Avaya Cajun P333T Скачать руководство пользователя страница 5

Avaya P333T User’s Guide

i

Table of Contents

Preface .................................................................................................................. I
FCC Notice........................................................................................................... I
Conventions Used in the Documentation ....................................................... I

CLI .............................................................................................................I
Notes, Cautions and Warnings ............................................................ II

Table of Contents ................................................................................................ i

List of Figures .................................................................................................... ix

List of Tables ...................................................................................................... xi

Chapter 1

Avaya P330 Overview.......................................................................................  1
Avaya P330 Family Features ............................................................................  1
Avaya P330 Standards Supported...................................................................  2

IEEE .......................................................................................................... 2
IETF ........................................................................................................... 2

Avaya P330 Network Management ................................................................  2

Avaya P330 Device Manager (Embedded Web)  ................................ 2
Avaya P330 Command Line Interface (CLI) ....................................... 2
Avaya Multi-Service Network Manager™  ......................................... 3

Avaya P330 Network Monitoring ...................................................................  3

RMON MIBs - RFC 1757 ........................................................................ 3
SMON MIBs - RFC 2613  ........................................................................ 3
Bridge MIB Groups - RFC 2674  ............................................................ 3
Port Mirroring  ......................................................................................... 3
SMON ....................................................................................................... 4

Chapter 2

Applications........................................................................................................  5
Application 1 ......................................................................................................  5
Application 2 ......................................................................................................  6
Application 3 ......................................................................................................  7

Chapter 3

Avaya P333T Front and Back Panels...............................................................  8
Avaya P333T Front Panel..................................................................................  8
Avaya P330 Back Panel ...................................................................................  11

BUPS Input Connector ......................................................................... 11

Chapter 4

Installation and Setup......................................................................................  19
Installing the X330STK Stacking Sub-module in the P330.........................  19

Содержание Cajun P333T























































































































































































Отзывы:

Нет отзывов