Avaya Cajun P333T Скачать руководство пользователя страница 144

Страница: 144 / 182

Chapter 6

CLI – Layer 2

128

Avaya P333T User’s Guide

alarm 1026 was created successfully

rmon event

Use the

rmon event

command to create an RMON event entry.

The syntax for this command is:

rmon event <Event Number> <type> description <description>

owner <owner>

Output Example:

P330-N# rmon event 1054 logAndTrap description "event for

monitoring amir's computer" owner amir

event 1054 was created successfully

copy stack-config tftp

Use the

copy stack-config tftp

command to upload the stack-level

parameters from the current NVRAM running configuration into a file via TFTP.

Note:

Create the file into which you wish to upload the stack-level parameters prior

to executing this command.

The syntax for this command is:

copy stack-config tftp <filename> <ip>

Output Example:

P330-N# copy stack-config tftp c:\conf.cfg 192.168.49.10

Beginning upload operation ...

event number

This is the event index number of this entry.

type

The type of the event. The possible parameters are:
trap, log, logAndTrap, none.

description

A user description of this event

owner

Owner name string

filename

The file name (full path)

The IP address of the TFTP server

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 144 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: