manualshive.com logo in svg

Avaya Cajun P333T, Руководство пользователя, Страница: 136 / 182

Поделиться
Скачать
Avaya Cajun P333T Скачать руководство пользователя страница 136

Chapter 6

CLI – Layer 2

120

Avaya P333T User’s Guide

The syntax for this command is:

set secure mac <mac-address> port <mod-num>/<port-num>

set security mode

Use the 

set security mode

 command to enable or disable MAC security at the 

stack level. When enabled, the ports are secured based on their individual 
configuration. When disabled, all the ports in a stack are non-secured. 

The syntax for this command is:

set security mode { enable | disable }

Output Example:

P330-N> set security mode enable

Security mode enabled.

set arp-aging-interval

Use this command to set the ARP table aging interval for gateways’ entries in the 
agent ARP table. The MAC value for the default gateway of ML agent in the ARP 
table, is deleted at the end of every aging interval. The default value is 10 minutes. 

The syntax for this command is:

set arp-aging-interval <value>

Example:

P330-N# set arp-aging-interval 20

ARP aging interval was set to 20 minutes.

set arp-tx-interval

Use the set arp-tx-interval command to set the keep-alive frames sending interval. 
Setting the interval to 0 disables the transmission of the keep-alive frames.

The syntax for this command is:

set arp-tx-interval <value>

value

The number representing the interval, from 0-10 minutes.

value

The interval, in seconds.

Содержание Cajun P333T























































































































































































Отзывы:

Нет отзывов