Avaya Cajun P333T Скачать руководство пользователя страница 59

Страница: 59 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

• show port self-loop-

discovery

Displays which port or switch has an
enabled IBM™ token ring cable loop
discovery status.

Page 57

• show internal

buffering

Shows the current internal buffering
capacity.

Page 57

• show boot bank

Displays the software bank from which
the switch will load.

Page 58

• show module

Shows switch status and information.

Page 58

• show port

flowcontrol

Shows the per-port status information
related to flow control.

Page 60

• show cam

Shows the CAM table entries for a
specific port.

Page 62

• show cascading fault-

monitoring

Shows cascading fault monitoring mode.

Page 62

• show port auto-

negotiation-
flowcontrol-
advertisement

Displays the flowcontrol advertisement
for a Gigabit port when performing
autonegotiation.

Page 63

• show trunk

Displays VLAN tagging information of
the ports, port binding mode, and the
port VLAN ID.

Page 63

• show vlan

Displays the VLANs configured in the
stack/switch.

Page 64

• show leaky-vlan

Displays the leaky VLAN status.

Page 65

• show spantree

Shows Spanning Tree Protocol (STP)
settings.

Page 65

• show autopartition

Shows the autopartition settings.

Page 67

• show dev log file

Displays the encrypted device log file.

Page 67

• show log

Displays an encrypted device reset log.

Page 67

• show module-

identity

Displays the switch’s identity.

Page 68

• show license

Shows the license.

Page 68

• show system

Shows system parameters.

Page 69

• show rmon statistics

Shows the traffic statistics of an interface.

Page 70

• show rmon history

Shows the existing history entries.

Page 71

• show rmon alarm

Shows the existing alarm entries.

Page 71

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 59 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: