manualshive.com logo in svg

Avaya Cajun P333T, Руководство пользователя, Страница: 44 / 182

Поделиться
Скачать
Avaya Cajun P333T Скачать руководство пользователя страница 44

Chapter 4

Installation and Setup

28

Avaya P333T User’s Guide

Cabling

Avaya P330 modules include the following types of ports (according to the speed 
and standard they support): 10Base-T, 100Base-TX, 100Base-FX, 1000Base-SX and 
1000Base-LX. 

Note:  

To interconnect Avaya P330 switches with twisted pairs, crossed cables are 

required.

•

The maximum UTP cable length connected to a 10/100 Mbps port operating as 
10Base-T, is 100 m (328 ft.).

•

A UTP Category 5 cable must be connected to any 100Base-TX port, via an RJ45 
connector. The maximum UTP cable length connected to a 10/100 Mbps port 
operating as 100Base-TX, is 100 m (328 ft.).

•

A fiberoptic cable must be connected to any 100Base-FX port, via a pair of SC 
connectors. The maximum fiber cable length connected to a 100Base-FX port is 
412 m (1,352 ft) when operating in half duplex, and 2 km (6,562 ft) when 
operating in full duplex.

Appropriate cables are available from your local supplier.

Table 4.3

Gigabit Ethernet Cabling

Gigabit 
Interface

Fiber 
Type

Diameter 
(

µ

m)

Modal 
Bandwidth 
(MhzKm)

Maximum 
Distance 
(m)

Minimum 
Distance 
(m)

Wavelength 
(nm)

1000BASE-SX

MM

62.5

160

220

2

850

1000BASE-SX

MM

62.5

200

275

2

850

1000BASE-SX

MM

50

400

500

2

850

1000BASE-SX

MM

50

500

550

2

850

1000BASE-LX

MM

62.5

500

550

2

1310

1000BASE-LX

MM

50

400

550

2

1310

1000BASE-LX

SM

9

NA

10,000

2

1310

Содержание Cajun P333T























































































































































































Отзывы:

Нет отзывов