Avaya Cajun P333T Скачать руководство пользователя страница 90

Страница: 90 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show tftp download/upload status

Use the

show tftp download status

and

show tftp upload status

commands to display the status of the current TFTP configuration file copy process
into/from the device.

The syntax for this command is:

show tftp {download|upload} status [<mod_num>]

Output Example:

P330-N> show tftp upload status 1

Module : 1

Source file : stack-config

Destination file : c:\conf.cfg

Host : 149.49.36.200

Running state : Executing

Failure display : (null)

Last warning : No-warning

show tftp download software status

Use the

show tftp download software status

commands to display the

status of the current TFTP Device Manager S/W (Embedded Web) download
process into the device.

The syntax for this command is:

show tftp download software status [<mod_num>]

Output Example:

P330-1(super)# show tftp download software status

Module #1

===========

Module : 1

Source file : d:\p340sw\gt-ml\3.5.18\p340.web

Destination file : EW_Archive

Host : 149.49.70.61

Running state : Writing ...

Failure display : (null)

Last warning : No-warning

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 90 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: