Avaya Cajun P333T Скачать руководство пользователя страница 81

Страница: 81 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show leaky-vlan

Use the

show leaky-vlan

command to display the leaky VLAN status.

The syntax for this command is:

show leaky-vlan

Output Example:

P330-N> show leaky-vlan

Leaky VLAN mode Disable

show spantree

Use the

show spantree

command to display spanning-tree information.

The syntax for this command is:

show spantree [<mod_num>[/<port_num>]]

Output Example:

P330-N> show spantree

Spanning tree enabled

Designated Root: 00-40-0d-88-06-c8

Designated Root Priority: 32768

Designated Root Cost: 20

Designated Root Port: 1/1

Root Max Age: 20 Hello Time: 2

Bridge ID MAC ADDR: 00-40-0d-92-04-b4

Bridge ID priority: 32768

Port State Cost Priority

------ ------------- ---------- ------------

1 /1 Forwarding 20 128

1 /2 not-connected 20 128

1 /3 LAG-member 20 128

1 /4 LAG-member 20 128

1 /5 not-connected 20 128

1 /6 not-connected 20 128

etc...

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 81 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: