Avaya Cajun P333T Скачать руководство пользователя страница 64

Страница: 64 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show snmp retries

Use the

show snmp retries

command to display the number of retries initiated

by the Device Manager application when it tries to send SNMP messages to the
device.

The syntax for this command is:

show snmp retries

Output Example:

P330-N> show snmp retries

the SNMP Retries Number is 3

show snmp timeout

Use the

show snmp timeout

command to display the default SNMP timeout in

seconds. This command is useful for access using the Device Manager.

The syntax for this command is:

show snmp timeout

Output Example:

P330-N> show snmp timeout

the SNMP Timeout is 2000

show timeout

Use the

show timeout

command to display the amount of time the CLI can

remain idle before timing out in minutes. If the result is 0, there is no timeout limit.
The default is 15 minutes.

The syntax for this command is:

show timeout

Output Example:

P330-N> show timeout

CLI timeout is 10 minutes

show logout

Use the

show logout

command to display the amount of time the CLI can

remain idle before timing out in minutes. If the result is 0, there is no timeout limit.
The default is 15 minutes.

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 64 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: