Avaya Cajun P333T Скачать руководство пользователя страница 141

Страница: 141 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

125

reset mgp

Use the

reset mgp

command to perform a software reset in the G700 Media

Gateway Processor.

The syntax for this command is:

reset mgp

reset wan

Use the

reset wan

command to perform a software reset in the X330 WAN Access

Router Module.

The syntax for this command is:

reset wan [module number][bank-a]

Example:
To reset a WAN module residing on switch 2:

P330-N# reset wan 2

This command will force a switch-over to the wan device

and disconnect your telnet session

*** Reset *** - do you want to continue (Y/N)? y

nvram initialize

Use the

nvram initialize

command to reset the P330 parameters to the factory

defaults. If no options are specified for this command, only the Layer 2 parameters
will be reset.

module
number

Optional - the module number where the WAN module to be
reset resides.

bank-a

Optional - boot the WAN module from bank-a after reset.

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 141 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: