Avaya Cajun P333T Скачать руководство пользователя страница 91

Страница: 91 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show web aux-files-url

Use the

show web aux-files-url

command to display the URL/Directory

from where the P330 can access the Device Management auxiliary files (for example
help files).

The syntax for this command is:

show web aux-files-url

show intelligent-multicast

Use the

show intelligent-multicast

command to display the intelligent

multicast configuration.

The syntax for this command is:

show intelligent-multicast

Output Example:

P330-N> show intelligent-multicast

Intelligent-multicast configuration:

------------------------------------

intelligent-multicast state --------------------- Disabled

Intelligent-multicast client-port-pruning time --- 600[Sec]

Intelligent-multicast router-port-pruning time ---1800[Sec]

intelligent-multicast group-filtering-delay time - 10[Sec]

Intelligent-multicast HW configuration:

# Module Sub-Module Cascade

------- ---------- --------

1 No IPMc Support Not Installed No IPMc Support

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 91 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: