Avaya Cajun P333T Скачать руководство пользователя страница 102

Страница: 102 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

clear port static-vlan

Use the

clear port static-vlan

command to delete VLANs statically

configured on a port.

The syntax for this command is:

clear port static-vlan [module/port range][vlan num]

Output Example:

P330-1(super)# clear port static-vlan 1/10 5

VLAN 5 is unbound from port 1/10

clear cam

Use the

clear cam

command to delete all entries from the CAM table.

The syntax for this command is:

clear cam

Output Example:

P330-N# clear cam

CAM table entry cleared.

clear log

Use the

clear log

command to delete the Log file of a switch.

The syntax for this command is:

clear log [<mod_num>]

clear port mirror

Use the

clear port mirror

command to cancel port mirroring.

The syntax for this command is:

clear port mirror <source-module>/<source-port>/<dest-

module>/<dest-port>

module/port
range

Port range

vlan num

The VLAN to unbind from the port

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 102 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: