Avaya Cajun P333T Скачать руководство пользователя страница 113

Страница: 113 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

set device-mode

Use the

set device-mode

command to change the Basic Mode of Operation of

the P332-ML/P332GT-ML/P333R/P333R-LB switches between Router and Layer 2
modes.

Note:

This command is not supported by the P333T/P334T/P332MF switches

which do not have Router mode.

The syntax for this command is:

set device-mode <mode>

set interface

Use the

set interface

command to configure the management interface on the

Master agent of the stack.

The syntax for this command is:

set interface inband <vlan> <ip_addr> <netmask>

Output Example:

P330-N# set interface inband 1 192.168.42.252 255.255.255.0

Interface inband IP address set.

You must reset the device in order for the change to take effect.

mode

Router | Layer2

inband

Interface name used for the management

vlan

The number of the VLAN to be used for management

ip_addr

IP address used for managing the stack

netmask

Subnet mask of the management interface

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 113 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: