Avaya Cajun P333T Скачать руководство пользователя страница 62

Страница: 62 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show ip route

Use the

show ip route

command to display IP routing table entries.

The syntax for this command is:

show ip route

Output Example:

P330-N> show ip route

show image version

Use the

show image version

command to display the software version of the

image on both memory banks of a specified switch.

The syntax for this command is:

show image version [<mod_num>]

If no switch number is specified, the image version of the all switches will be
displayed.

Output Example:

P330-N> show image version 1

Mod Module-Type Bank Version

------ ----------- ---- --------

1 24x10/100Base-T with optional expansion slot A 3.3.14

1 24x10/100Base-T with optional expansion slot B 3.5.19

Destination

Gateway

-----------

149.49.1.1

172.20.22.201

190.20.0.0

172.20.22.202

172.20.0.0

172.20.22.96

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 62 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: