Avaya Cajun P333T Скачать руководство пользователя страница 133

Страница: 133 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

117

set ppp authentication incoming

Use the

set ppp authentication

incoming

command to define the

authentication method used for a PPP server or client session.

The syntax for this command is:

set ppp authentication incoming

{pap|chap|none}

Example:

P330-N(super)# set ppp authentication incoming chap

set ppp incoming timeout

Use the

set ppp

incoming timeout

command to configure the number of

minutes until the system automatically disconnects an idle PPP incoming session.

The syntax for this command is:

set ppp incoming timeout <time>

Output Example:

P330-N> set ppp incoming timeout 15

PPP incoming session will automatically disconnect after 15

minutes of idle time

set ppp baud-rate

Use the set ppp baud-rate command to define the baud rate used in PPP sessions.
Note that the peer baud rate must be set at the same value as the host.

The syntax for this command is:

set ppp baud-rate <9600 | 19200 | 38400>

Example:

P330-N# set ppp baud-rate 38400

pap

PAP authentication method

chap

CHAP authentication method

none

No authentication

time

The timeout in minutes

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 133 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: