Avaya Cajun P333T Скачать руководство пользователя страница 172

Страница: 172 / 182

Appendix A

Specifications

156

Avaya P333T User’s Guide

Environmental

Safety

•

UL for US approved according to UL195O Std.

•

C-UL(UL for Canada) approved according to C22.2 No.950 Std.

•

CE for Europe approved according to EN 60950 Std.

•

Overcurrent Protection: A readily accessible Listed safety-approved protective
device with a 16A rating must be incorporated in series with building
installation AC power wiring for the equipment under protection.

EMC Emissions

Emissions

Approved according to:
•

Europe - EN55022 class A, 1994

•

Europe - EN 6150-3-2 (Harmonics Current Emissions

•

Europe - EN 6150-3-3 (Flicker)

Immunity

Approved according to:
•

EN 50082-1

•

IEC 150-4-5

BUPS MTBF

•

125,194 hrs minimum (see Section MTBF in Various Configurations)

Operating Temp.

0-50

C (32-122

Rel. Humidity

5% to 95% non-condensing

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 172 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: