Avaya Cajun P333T Скачать руководство пользователя страница 82

Страница: 82 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

Output Fields:

Field

Description

Spanning tree

Status of whether Spanning-Tree Protocol is enabled or
disabled

Designated
Root

MAC address of the designated spanning-tree root bridge

Designated
Root Priority

Priority of the designated root bridge

Designated
Root Cost

Total path cost to reach the root

Designated
Root Port

Port through which the root bridge can be reached (shown only
on nonroot bridges)

Root Max Age

Amount of time a BPDU packet should be considered valid

Hello Time

Number of times the root bridge sends BPDUs

Bridge ID
MAC ADDR

Bridge MAC address used in the sent BPDUs

Bridge ID
Priority

Bridge priority

Port

Port number

State

Spanning-tree port state (disabled, inactive, not-connected,
blocking, listening, learning, forwarding, bridging, or type-
pvid-inconsistent)

Cost

Cost associated with the port

Priority

Priority associated with the port

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 82 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: