Avaya Cajun P333T Скачать руководство пользователя страница 60

Страница: 60 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

• show rmon event

Shows the existing event entries.

Page 72

• show ppp session

Shows the PPP parameters of the active
PPP session.

Page 72

• show ppp

authentication

Shows the authentication method used
for PPP sessions.

Page 72

• show ppp incoming

timeout

Shows the amount of time PPP sessions
can remain idle before being
disconnected.

Page 73

• show ppp baud-rate

Shows the baud rate.

Page 73

• show ppp

configuration

Displays the ppp configuration.

Page 73

• show tftp upload/

download status

Shows the status of the TFTP upload/
download configuration per switch.

Page 74

• show tftp download

software status

Shows the status of the TFTP software
download of the Device Manager
software to the switch.

Page 74

• show web

aux-files-url

Shows the location (URL/directory) of
the P330 Device Manager Help files.

Page 75

• show intelligent-

multicast

Shows the status IP multicast filtering
application.

Page 75

• show intelligent-

multicast hardware
support

Shows whether the connected unit’s
hardware supports IP multicast filtering.

Page 76

• show security mode

Displays the status of the MAC security
feature (enabled/disabled).

Page 76

• show secure mac port

Shows the secure MAC addresses of a
port.

Page 77

• show arp-tx-interval

Displays the keep-alive status.

Page 77

• show arp-aging-

interval

Displays the ARP table aging interval for
gateways’ entries.

Page 77

• show self-loop

discovery

Displays the self-loop discovery mode.

Page 78

• show allowed

managers status

Displays the status of the allowed
managers feature (enabled/disabled) .

Page 78

• show allowed

managers table

Displays the IP addresses of the allowed
managers.

Page 79

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 60 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: