Avaya Cajun P333T Скачать руководство пользователя страница 152

Страница: 152 / 182

Chapter 6

CLI – Layer 2

136

Avaya P333T User’s Guide

show username

Use the

show username

command to display the username.

The syntax for this command is:

show username

Output Example:

P330-N> show username

User account password access-type

-------------- ------------------------------ -----------

root **** admin

set ppp chap-secret

Use the

set ppp chap-secret

command to configure the shared secret used in

PPP sessions with CHAP authentication.

The syntax for this command is:

set ppp chap-secret <chap-secret>

Output Example:

P330-N(super)# set ppp chap secret sodot

PPP shared secret for CHAP authentication is set

show radius authentication

Use the

show radius authentication

command to display all RADIUS

authentication configurations. The shared secrets are not displayed.

The syntax for this command is:

show radius authentication

chap-secret

The shared secret, 4 to 32 characters.

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 152 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: