Avaya Cajun P333T Скачать руководство пользователя страница 92

Страница: 92 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show intelligent-multicast hardware-support

Use the

show intelligent-multicast hardware-support

command to

display the intelligent multicast hardware support configuration.

The syntax for this command is:

show intelligent-multicast hardware-support

Output Example:

P330-N> show intelligent-multicast hardware support

Intelligent-multicast HW configuration:

# Module Sub-Module Cascade

------- ---------- --------

1 Support IPMc Not Installed Support IPMc

show security mode

Use the

show security mode

command to display the status of the MAC

security feature.

Note:

Layer 2 commands are only available if you open a

switch

session with the

Master switch.

The syntax for this command is:

show security mode

Output Example:

P330-N> show security mode

Security mode enabled.

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 92 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: