manualshive.com logo in svg

Avaya Cajun P333T, Руководство пользователя, Страница: 77 / 182

Поделиться
Скачать
Avaya Cajun P333T Скачать руководство пользователя страница 77

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

61

Output Fields 

Field

Description 

Port

Switch and port number

Send-
Flowcontrol- 
Admin

Send flow-control administration. Possible settings:
• ON indicates that the local port is allowed to send flow 

control frames to the far end.

• OFF indicates that the local port is not allowed to send flow 

control frames to the far end.

Send-
Flowcontrol- 
Oper

Send flow-control operation mode. Possible modes:
• ON indicates that the local port will send flow control frames 

to the far end.

• OFF indicates that the local port will not send flow control 

frames to the far end.

Receive-
Flowcontrol- 
Admin

Receive flow-control administration. Possible settings:
• ON indicates that the local port will act upon flow control 

indications if received from the far end.

• OFF indicates that the local port will discard flow control 

frames if received from the far end.

Receive-
Flowcontrol- 
Oper

Receive flow-control operation mode. Possible modes:
• ON indicates that the local port will act upon flow control 

indications received from the far end.

• OFF indicates that the local port will discard flow control 

frames received from the far end.

Содержание Cajun P333T























































































































































































Отзывы:

Нет отзывов