Avaya Cajun P333T Скачать руководство пользователя страница 69

Страница: 69 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show intermodule port redundancy

Use the

show intermodule redundancy

command to display the intermodule

redundancy entry defined for the stack.

The syntax for this command is:

show intermodule port redundancy

Output Example:

P330-N> show intermodule port redundancy

Primary-Port : 1/1

Primary-Port status : Disable

Secondary-Port : 1/2

Secondary-Port status : Disable

show port mirror

Use the

show port mirror

command to display mirroring information for the

stack.

The syntax for this command is:

show port mirror [<mod_num>[/<port_num>]]

Output Example:

P330-N> show port mirror

port mirroring

Mirroring both Rx and Tx packets from port 1/2 to port 1/4 is

enabled

show port vlan-binding-mode

Use the

show port vlan-binding-mode

command to display port vlan binding

mode information.

The syntax for this command is:

show port vlan-binding-mode [module[/port]]

module/port

The switch number/the port
number

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 69 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: