manualshive.com logo in svg

Avaya Cajun P333T, Руководство пользователя, Страница: 170 / 182

Поделиться
Скачать
Avaya Cajun P333T Скачать руководство пользователя страница 170

Appendix A

Specifications

154

Avaya P333T User’s Guide

ATM Expansion Modules

There are three Avaya P330 ATM Expansion Modules:
•

X330-OC12F1:

500m, Multimode fiber, can also be OC-3 reduced range

•

X330-OC12S1:

15 km, Single-mode fiber, can also be OC-3

The ATM Modules can be installed in the following Avaya P330 Family switches:
•

Avaya P333T Hardware Version C/S 1.3 and higher, with Embedded S/W 2.4 
and higher.

Note:  

The ATM Expansion Module cannot be used in Avaya P333T hardware 

Versions lower than C/S 1.3.

•

Avaya P334T Embedded S/W Ver. 2.4 and higher.

•

Avaya P332MF Embedded S/W Ver. 3.0 and higher.

•

Avaya P333R Embedded S/W Ver. 2.4 and higher.

Refer to the Avaya X330 ATM Access Module Installation Guide for installation 
procedures. 
The multimode Avaya X330-OC12F1 and X330-OC3F1 (future) ATM Modules are 
Class 1 LED products. The single-mode X330-OC12S1 ATM Module is a Class 1 
Laser product. They comply with EN 60825-1 and Food and Drug Administration 
(FDA) 21 CFR 1040.10 and 1040.11.

The Modules must be operated under recommended operating conditions.

Safety Information

Single-mode Module Laser Classification

Note:  

Class 1 lasers are inherently safe under reasonably foreseeable conditions of 

operation.

Caution:  

The use of optical instruments with this product will increase eye hazard.

CLASS 1 

LASER PRODUCT

Содержание Cajun P333T























































































































































































Отзывы:

Нет отзывов