Avaya Cajun P333T Скачать руководство пользователя страница 106

Страница: 106 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

• set port spantree cost

Sets the port spantree cost.

Page 110

• set port security

Enables MAC security on a range of
ports.

Page 111

• set cascading

Sets switch cascading fault-monitoring
mode.

Page 111

• set inband vlan

Sets the management VLAN ID.

Page 111

• set vlan

Creates VLANs.

Page 112

• set port flowcontrol

Sets the flow control mode of a port.

Page 112

• set port auto-

negotiation-
flowcontrol-
advertisement

Sets the flowcontrol advertising
capabilities of a Gigabit port.

Page 114

• set trunk

Sets the tagging mode of a port.

Page 114

• set leaky-vlan

Enables/disables leaky-VLAN mode.

Page 115

• set spantree

Enables/disables Spanning Tree
Protocol (STP).

Page 115

• set spantree priority

Sets the STP Bridge priority level.

Page 115

• set autopartition

Enables or disables autopartitioning for
switches in a stack.

Page 116

• set license

Enters a license number for the stack.

Page 116

• set ppp authentication

incoming

Defines the PPP authentication method.

Page 117

• set ppp incoming

timeout

Sets the time after which the system
automatically disconnects an idle PPP
incoming session.

Page 117

• set ppp baud-rate

Sets the baud rate used in PPP sessions.

Page 117

• set web

aux-files-url

Sets the location (URL/directory) of the
P330 Device Manager Help files.

Page 118

• set intelligent-multicast

Enables or disables the IP multicast
filtering application.

Page 118

• set intelligent-multicast

client-port-pruning
time

Sets the aging time for client ports.

Page 118

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 106 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: