Avaya Cajun P333T Скачать руководство пользователя страница 130

Страница: 130 / 182

Chapter 6

CLI – Layer 2

114

Avaya P333T User’s Guide

set port auto-negotiation-flowcontrol-advertisement

The

set port auto-negotiation-flowcontrol-advertisement

command

sets the flowcontrol advertisement for a Gigabit port when performing
autonegotiation.

The syntax for this command is:

set port auto-negotiation-flowcontrol-advertisement <mod_num>/

<port_num> {no-flowcontrol|asym-tx-only|sym-only|sym-and-asym-rx}

Output Example:

P330-N# set port auto-negotiation-flowcontrol-advertisement

1/5 asym-tx-only

P330-N# Port 1/5 pause capabilities was set

set trunk

Use the

set trunk

command to configure the tagging mode of a post.

set trunk [module/port] [value]

Output Example:

P330-1(super)# set trunk 2/20 dot1q

Dot1Q VLAN tagging set on port 2/20.

no-flowcontrol

The port will advertise no pause capabilities.

asym-tx-only

The port will advertise asymmetric Tx pause capabilities only.

sym-only

The port will advertise symmetric pause capabilities only.

sym-and-asym-rx

The port will advertise both symmetric and asymmetric Rx
pause capabilities.

module/port

module/port number

value

off/dot1q

Содержание Cajun P333T























































































































































































Результаты поиска

Содержание Cajun P333T

Отзывы:

Avaya Cajun P333T, Руководство пользователя, Страница: 130 / 182

Результаты поиска

Содержание Cajun P333T

Отзывы: