AudioCodes Mediant 500 E-SBC Скачать руководство пользователя страница 784 | Manualshive

Страница: 784 / 920

background image

User's Manual

784

Document #: LTRT-10437

Mediant 500 E-SBC

Parameter

Description

The valid range is 0 to 1023. The default is 0.

Web: Answer Detector Silence Time

[AnswerDetectorSilenceTime]

Currently, not supported.

Web: Answer Detector Redirection

[AnswerDetectorRedirection]

Currently, not supported.

Web: Answer Detector Sensitivity
EMS: Sensitivity
CLI: answer-detector-sensitivity

[AnswerDetectorSensitivity]

Defines the Answer Detector sensitivity.

The range is 0 (most sensitive) to 2 (least sensitive). The
default is 0.

54.9.2 Coder Parameters

The coder parameters are described in the table below.

Table

54-34: Coder Parameters

Parameter

Description

Silk Tx Inband FEC
CLI: silk-tx-inband-fec
[SilkTxInbandFEC]

Enables forward error correction (FEC) for the SILK coder.



[0]

Disable (default)



[1]

Enable

Silk Max Average Bit Rate
CLI: silk-max-average-bitrate
[SilkMaxAverageBitRate]

Defines the maximum average bit rate for the SILK coder. The valid
value range is 5000 to 30000. The default is 16000.

Note:

The SILK coder is Skype's default audio codec used for

Skype-to-Skype calls.

EMS: VBR Coder Header
Format
CLI: VBR-coder-header-format
[VBRCoderHeaderFormat]

Determines the format of the RTP header for VBR coders.



[0]

= (Default) Payload only (no header, TOC, or m-factor) -

similar to RFC 3558 Header Free format.



[1]

= Supports RFC 2658 - 1 byte for interleaving header

(always 0), TOC, no m-factor.



[2]

= Payload including TOC only, allow m-factor.



[3]

= RFC 3558 Interleave/Bundled format.

EMS: VBR Coder Hangover
CLI: VBR-coder-hangover
[VBRCoderHangover]

Defines the required number of silence frames at the beginning of
each silence period when using VBR coder silence suppression.
The range is 0 to 255. The default is 1.

Web: AMR Payload Format
[AmrOctetAlignedEnable]

Defines the AMR payload format type.



[0]

Bandwidth Efficient



[1]

Octet Aligned (default)

EMS: AMR Coder Header
Format
[AMRCoderHeaderFormat]

Determines the payload format of the AMR header.



[0]

= Non-standard multiple frames packing in a single RTP

frame. Each frame has a CMR and TOC header.



[1]

= AMR frame according to RFC 3267 bundling.



[2]

= AMR frame according to RFC 3267 interleaving.



[3]

= AMR is passed using the AMR IF2 format.

Note:

Bandwidth Efficient mode is not supported; the mode is

always Octet-aligned.

«
...
782
783
784
785
786
...
»

Содержание Mediant 500 E-SBC

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Mediant 500 E-SBC

Бренд: Ideal Life Страницы: 16

Бренд: Spectrum Brands Страницы: 2

P-660HN-Fx series

Бренд: ZyXEL Communications Страницы: 12

Бренд: Edimax Страницы: 27

Бренд: LifeShield Страницы: 2

Бренд: Zte Страницы: 14

Бренд: QEI Страницы: 47

Бренд: Inovonics Страницы: 13

Бренд: ZyXEL Communications Страницы: 20

Бренд: Watchguard Страницы: 32

Бренд: Rosslare Страницы: 28

Бренд: Rosslare Страницы: 52

Бренд: 2N Telekomunikace Страницы: 105

Бренд: 4IPNET Страницы: 368

Бренд: Pace Страницы: 23

Бренд: Juniper Страницы: 154

Бренд: Juniper Страницы: 172

Бренд: Juniper Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды