AudioCodes Mediant 500 E-SBC Скачать руководство пользователя страница 316 | Manualshive

Страница: 316 / 920

background image

User's Manual

316

Document #: LTRT-10437

Mediant 500 E-SBC

Parameter

Description

TxDTMFOption

Web: Rx DTMF Option
CLI: rx-dtmf-option
[IpProfile_RxDTMFOption]

Enables the device to declare the RFC 2833 'telephony-
event' parameter in the SDP.



[0]

Not Supported



[3]

Supported (default)

The device is always receptive to RFC 2833 DTMF relay
packets. Thus, it is always correct to include the 'telephony-
event' parameter by default in the SDP. However, some
devices use the absence of the 'telephony-event' in the SDP
to decide to send DTMF digits in-band using G.711 coder. If
this is the case, set this parameter to 0.

Note:

The corresponding global parameter is

RxDTMFOption.

Web: Hold
CLI: enable-hold
[IpProfile_EnableHold]

Enables the interworking of the Hold/Retrieve supplementary
service from ISDN PRI to SIP (digital interfaces).



[0]

Disable



[1]

Enable (default)

Notes:



Digital interfaces: To interwork the Hold/Retrieve
supplementary service from SIP to ISDN (QSIG and Euro
ISDN), set the EnableHold2ISDN parameter to 1.



The corresponding global parameter is EnableHold.

Web: Add IE In Setup
CLI: add-ie-in-setup
[IpProfile_AddIEInSetup]

Defines an optional Information Element (IE) data (in hex
format) which is added to ISDN Setup messages. For
example, to add IE '0x20,0x02,0x00,0xe1', enter the value
"200200e1".

Notes:



This IE is sent from the Trunk Group IDs that are defined
by the SendIEonTG parameter .



You can configure different IE data for Trunk Groups by
configuring this parameter for different IP Profiles and
then assigning the required IP Profile ID in the Inbound IP
Routing table (PSTNPrefix).



This feature is similar to that of the
EnableISDNTunnelingIP2Tel parameter. If both
parameters are configured, the
EnableISDNTunnelingIP2Tel parameter takes
precedence.



The corresponding global parameter is AddIEinSetup.

Web: QSIG Tunneling
CLI: enable-qsig-tunneling
[IpProfile_EnableQSIGTunneling]

Enables QSIG tunneling-over-SIP for this SIP entity. This is
according to IETF Internet-Draft draft-elwell-sipping-qsig-
tunnel-03 and ECMA-355 and ETSI TS 102 345.



[0]

Disable (default).



[1]

Enable = Enables QSIG tunneling from QSIG to SIP,

and vice versa. All QSIG messages are sent as raw data
in corresponding SIP messages using a dedicated
message body.

Notes:



QSIG tunneling must be enabled on originating and
terminating devices.



To enable this function, set the

«
...
314
315
316
317
318
...
»

Содержание Mediant 500 E-SBC

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Mediant 500 E-SBC

Бренд: AccessZone Страницы: 7

Бренд: EchoLife Страницы: 16

Бренд: RTA Страницы: 93

Бренд: ICU tech Страницы: 17

Бренд: Gateway Страницы: 2

ONLY SMART HOME D-FTC2E

Бренд: ENANCER Страницы: 9

Бренд: Ubee Страницы: 103

Бренд: SharkRF Страницы: 131

VBG-PN-K20-DMD-EV

Бренд: Pepperl+Fuchs Страницы: 11

Бренд: Ubee Страницы: 7

Бренд: Xentino Страницы: 126

Бренд: ECKELMANN Страницы: 34

INSOMNIAC CIA G-600

Бренд: Opentech Страницы: 13

Бренд: Technicolor Страницы: 106

3CRWE51196 - OfficeConnect Wireless Cable/DSL...

Бренд: 3Com Страницы: 88

Бренд: RTA Страницы: 74

Бренд: RTA Страницы: 81

Бренд: D-Link Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды