AudioCodes Mediant 500 E-SBC Скачать руководство пользователя страница 312 | Manualshive

Страница: 312 / 920

background image

User's Manual

312

Document #: LTRT-10437

Mediant 500 E-SBC

Parameter

Description

The SDP contains the following line:

'a=rtpmap:100 X-NSE/8000'.

Notes:



When enabled, the following conditions must also be met:



The Cisco gateway must include the following
definition:
'modem passthrough nse payload-type 100 codec
g711alaw'.



Set the Modem transport type to Bypass mode
(VxxModemTransportType is set to 2) for all
modems.



Set the NSEPayloadType parameter to 100.



The corresponding global parameter is NSEMode.

Web: Play RB Tone to IP
CLI: play-rbt-to-ip
[IpProfile_PlayRBTone2IP]

Enables the device to play a ringback tone to the IP side for
IP-to-Tel calls.



[0]

Disable (Default)



[1]

Enable = Plays a ringback tone after a SIP 183

session progress response is sent.

Notes:



To enable the device to send a 183/180+SDP responses,
set the EnableEarlyMedia parameter to 1.



If the EnableDigitDelivery parameter is set to 1, the
device doesn't play a ringback tone to IP and doesn't
send 183 or 180+SDP responses.



Digital interfaces: If this parameter is enabled and
EnableEarlyMedia is set to 1, the device plays a ringback
tone according to the following:



CAS: The device opens a voice channel, sends a
183+SDP response, and then plays a ringback tone
to IP.



ISDN: If a Progress or an Alerting message with PI (1
or 8) is received from the ISDN, the device opens a
voice channel, sends a 183+SDP or 180+SDP
response, but doesn't play a ringback tone to IP. If PI
(1 or 8) is received from the ISDN, the device
assumes that ringback tone is played by the ISDN
switch; otherwise, the device plays a ringback tone to
IP after receiving an Alerting message from the
ISDN. It sends a 180+SDP response, signaling to the
calling party to open a voice channel to hear the
played ringback tone.



The corresponding global parameter is PlayRBTone2IP.

Web: Early Media
CLI: early-media
[IpProfile_EnableEarlyMedia]

Enables the Early Media feature for sending media (e.g.,
ringing) before the call is established.



[0]

Disable (default)



[1]

Enable



Digital: The device sends a SIP 18x response with
SDP, allowing the media stream to be established
before the call is answered.

Notes:



Digital: The inclusion of the SDP in the 18x response
depends on the ISDN Progress Indicator (PI). The SDP is

«
...
310
311
312
313
314
...
»

Содержание Mediant 500 E-SBC

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Mediant 500 E-SBC

Бренд: WAGO Страницы: 76

Бренд: THOMSON Страницы: 52

Бренд: Alcatel-Lucent Страницы: 2

Бренд: PTT Страницы: 21

Бренд: NEC Страницы: 81

Бренд: Peavey Страницы: 41

UNIGATE EL-DeviceNet

Бренд: DEUTSCHMANN AUTOMATION Страницы: 62

UNIGATE CM - PROFIBUS

Бренд: DEUTSCHMANN AUTOMATION Страницы: 62

Wine Cap MWDG-ETH

Бренд: Capetti Elettronica Страницы: 6

Wireless DSL Gateway GT704WG-QW04

Бренд: ActionTec Страницы: 97

MiniHub Pro WLRRTES-102 TBMH110

Бренд: Browan Страницы: 14

Бренд: Technoton Страницы: 69

Бренд: 2N Страницы: 134

Бренд: Sierra Wireless Страницы: 74

Бренд: XAVi Страницы: 101

MULTIVOIP MVP-130

Бренд: Avaya Страницы: 1

Бренд: Weidmuller Страницы: 178

Бренд: rako Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды