Anritsu MD8470A Скачать руководство пользователя страница 94

Страница: 94 / 114

4.3 Cleaning

Turn off the main power supply on the rear panel and pull out the power

plug before cleaning the MD8470A.

4.3.1

Cleaning the cabinet

Follow the methods shown below when cleaning the exterior of the cabi-

net.

•

Wipe with a soft, clean cloth.

•

When dust or dirt is stuck to it or when it is to be stored for a long time,

wipe it with a cloth moistened in a neutral detergent. Then wipe it

with a soft, dry cloth.

•

If you find any loose screws or other parts, tighten them with the ap-

propriate tool.

CAUTION

Never use solvents like benzine, thinner or alcohol to clean

the cabinet. They may deteriorate or discolor the coating,

or distort the cabinet.

4.3.2

Cleaning others

Ensure that dust and dirt do not accumulate on or around this equipment.

In addition, shut off the main power and wipe water droplets, etc. adher-

ing to the power plug or connector with a dry cloth when they are adher-

ing to it.

WARNING

Clean the power inlet regularly. If dust accumulates

around the power pins, there is a risk of fire caused by

a tracking phenomenon.

keep the cooling fan clean so that the ventilation holes

are not obstructed. If the ventilation is obstructed,

the cabinet may overheat and catch fire.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 94 / 114

Результаты поиска

Содержание MD8470A

Отзывы: