Anritsu MD8470A Скачать руководство пользователя страница 90

Страница: 90 / 114

(5) Temperature stability test

Note:

Perform this test in a constant temperature tank free from vibra-

tion.

[Procedure]

During setup, set only the MD8470A in the constant temperature

tank (see the connection diagram shown in Fig. 4.1.4-1). Set the

tank temperature to 25

Turn on the MD8470A and wait until the temperature inside the

MD8470A is stabilized. (It takes about 1.5 hours until the tank

temperature becomes stable.)

After the temperature inside the MD8470A becomes stable, measure

the output frequency of the

10MHz Buff Output

connector on the

MD8470A using the frequency counter. Read values to the 0.1 Hz

digit (same for other measurements below).

Set the tank temperature to 40

When the temperatures inside the tank and for the MD8470A be-

come stable, measure the output frequency of the

10MHz Buff Output

connector on the MD8470A using the frequency counter.

Calculate stability using the equation below.

(Frequency counter value at 40

C) – (Frequency counter value at 25

Frequency
stability

(Frequency counter value at 25

Set the tank temperature to 5

When the temperatures inside the tank and for the MD8470A be-

come stable, measure the output frequency of the

10MHz Buff Output

connector on the MD8470A using the frequency counter.

Calculate stability using the equation below.

(Frequency counter value at 5

C) – (Frequency counter value at 25

Frequency
stability

(Frequency counter value at 25

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 90 / 114

Результаты поиска

Содержание MD8470A

Отзывы: