Anritsu MD8470A Скачать руководство пользователя страница 34

Страница: 34 / 114

2.1.2

Front panel

Fig. 2.1.2-1 Front panel (1)

Power switch

This is the switch to switch power ON or to standby (Stby).

RF connector

RF Main

Main I/O connector

This is an N-type main I/O connector. It is used as an input connec-

tor when

Input

is lit, as an output connector when

Output

is lit and as

an I/O connector when both

Input

and

Output

are lit.

RF Aux1

Aux1 I/O connector

This is an N-type auxiliary I/O connector. It is used as an input

connector when

Input

is lit, as an output connector when

Output

is lit

and as an I/O connector when both

Input

and

Output

are lit.

RF Aux2

Aux2 I/O connector

This is an N-type auxiliary I/O connector. It is used as an input

connector when

Input

is lit, as an output connector when

Output

is lit

and as an I/O connector when both

Input

and

Output

are lit.

CAUTION

Do not input power beyond the permissible maximum

power written on the label or in the specifications to the RF

input and output connectors. Do not input a signal to the

RF connector set to output. This may damage the internal

circuits and cause a fire or accident to occur.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 34 / 114

Результаты поиска

Содержание MD8470A

Отзывы: