Anritsu MD8470A Скачать руководство пользователя страница 88

Страница: 88 / 114

4.1.4 Reference oscillator frequency stability

The following describes frequency stability test methods of the 10 MHz

crystal oscillator being used as the reference oscillator. Evaluate the

stability by measuring the frequency change after 24-hour operation, and

the frequency change at ambient temperatures of 5

C and 40

(1) Performance test specifications

Table 4.1.4-1 Reference oscillator specification

Item

Specification

Frequency

10 MHz

Starting characteris-
tics

≤±

−

(5 minutes after power application,

based on the frequency after 24-hour opera-
tion as reference)

Aging rate

≤±

−

/day,

−

/year (after power ap-

plication, based on the frequency after 24-
hour operation as reference)

Temperature stabil-
ity

≤±

−

(25

C reference)

(2) Setup

Set up the performance test equipment as shown in Fig. 4.1.4-1.

Connect the

10MHz Buff Output

reference signal output connector on

the rear panel of the MD8470A and the input connector of the fre-

quency counter.

Frequency

standard

instrument

MF2412B

Output

MD8470A rear panel

Anritsu

MF2412A

Input

10MHz Buff Output

Name plate

Fig. 4.1.4-1 Setup of reference oscillator frequency stability test

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 88 / 114

Результаты поиска

Содержание MD8470A

Отзывы: