Anritsu MD8470A Скачать руководство пользователя страница 92

Страница: 92 / 114

4.2.3

Reference oscillator frequency calibration

This section describes the calibration method for the reference oscillator

frequency using the frequency counter. The 10 MHz reference oscillator

stability for the MD8470A is

−

/day. For frequency standard in-

strument, use a standard signal generator, which receives standard radio

wave of higher stability or sub-carrier of color TV broadcasting (signal

locked to the rubidium atomic standard instrument) and generates sig-

nals locked to this frequency standard instrument.

(1) Calibration specifications

Table 4.2.3-1 Reference oscillator specification

Item

Specification

Frequency

10 MHz

Starting characteris-
tics

≤±

−

(5 minutes after power application,

based on the frequency after 24-hour opera-
tion as reference)

Aging rate

≤±

−

/day,

−

/year (after power ap-

plication, based on the frequency after 24-
hour operation as reference)

Temperature stabil-
ity

≤±

−

(25

C reference)

(2) Setup

Set up the calibration equipment as shown in Fig. 4.2.3-1. Connect

the

10MHz Buff Output

reference signal output connector on the rear

panel of the MD8470A and the input connector of the frequency coun-

ter.

Frequency

standard

instrument

MF2412B

Output

MD8470A rear panel

Anritsu

MF2412A

Input

10MHz Buff Output

Freq Adj.

Name plate

Fig. 4.2.3-1 Setup of reference oscillator frequency calibration

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MD8470A



















































































































Результаты поиска

Содержание MD8470A

Отзывы:

Anritsu MD8470A, Руководство по эксплуатации, Страница: 92 / 114

Результаты поиска

Содержание MD8470A

Отзывы: